 |
MOD Manually Operated
Diaphragm Valve is ideal for Cyanoacrylates and other low
to medium viscosity fluids, for use in an operator applied situation.
Holding the lever down will apply the material, while a simple lift of the finger from
the lever
(shown left) will cause the diaphragm to close.
The
MOD
is hand actuated; no need for an
expensive
valve controller. For applications
with a controller, choose the AMD valve, for handheld
but more sophisticated and repeatable use.
For a typical valve setup,
click here.
Click here for the AMD,
the automatic timed shot version of this valve.
For full automation,
or when
mounted in a
valve stand or workstation,
click here.
|
|
In this Category:
Manual CA Valve
Auto CA Valve
Other Valves
You may also be
interested in:
Dispensers
Valve Controller
Dispense Valves
Reservoirs
Robot
Platform
Also of interest;
Precision Needles
Needle Nozzles
Thin Wall tips
Dispensing
Help
Doming & Potting
Solder Dispensing
|
|
To feed any IDS valve,
choose from our dispensing syringes, (to
feed thin to medium materials in very small shots) our
single cartridges, (for medium
to thicker materials in smaller shots or beads) or for large volume
capacity, order one of our
reservoirs (for thin to medium materials) or one of our
pail dispenser units, for thicker
materials.
MOD Diaphragm Valve
Features:
-
Silicone disk with Teflon® film
embedded on the wetted side.
-
Ergonomic wand construction for easy
handheld dispensing.
-
Delrin® material body.
-
Compact, low cost design.
-
Simple configuration
with pressure chamber (shown below).
Operation
-
Plumb
the material line.
-
Pressurize the fluid delivery
system and regulate the material to be dispensed with low pressure.
-
Cycle
the valve open by pressing the lever on the valve.
-
Fluid
should will begin to dispense from the tip of the valve.
-
Adjust
the pressure on the material inlet and connect the proper dispense tip to
the luer lock fitting on the end of the valve.
-
Turn the
valve upright with the tip pointing in the air.
-
Hold tip over a purge cup
or cover the tip with a cloth.
-
Trigger the valve to dispense until bubbles
clear the system.
-
Once
purged, dispensing can begin.
-
Material
inlet pressure and needle size will effect flow rate of material.
Specifications
Weight: 4.8 oz
Viscosity Range: 1 cps - 5,000 cps
Maximum Fluid Pressure: 60 PSI
Wetted Parts: Teflon®, Delrin®
Dimensions: 159 mm x 44.45
mm
Diameter: (6.258 in x 1.75 in Diameter)
Part #
Manual Diaphragm Valves and Kits
7020000 MOD
Handheld
Valve - manual lever
7020000SP Kit
for MOD Handheld - manual lever
For the MOD Package, order by the
following number:
7020014 Consists of one MOD
Manually held, Lever Actuated Valve, one
1 lb. Pressure Pot,
(black anodized aluminum body),
one
Valve Controller, all
necessary regulators, gauges, hoses, fittings, etc.
7020015 Consists of two
MOD Manually held, Lever Actuated Valve, one
1 lb. Pressure Pot,
(black anodized aluminum body),
one
Valve Controller, all
necessary regulators, gauges, hoses, fittings, etc.
7020016 Consists of one MOD
Manually held, Lever Actuated Valve, one
1 Gallon Pressure Pot, one
Valve Controller, and all
necessary regulators, gauges, hoses, fittings, etc.
|
|
